Posted in

What is telehandler load chart?

If you’ve ever stood on a construction job site, you’ve likely seen telehandlers in action—they’re those versatile workhorses that lift pallets of bricks, hoist HVAC units onto rooftops, and even reach over 3-story building edges to move supplies. But here’s the thing most new operators (or even some veteran crew leads) miss: a telehandler isn’t just a big truck with a boom. To use one safely and avoid costly, dangerous mistakes, you’ve got to know its load chart. As a telehandler supplier that’s been serving job sites across the Midwest for over a decade, I get questions about load charts all the time—usually from guys who just got their certification and are still figuring out how to turn those squiggly lines and numbers into actual work. Let’s break this down like I’d explain it to a new hire on my crew, no boring engineering jargon. Telehandlers

First, let’s get the basics straight: a telehandler load chart is like the machine’s rulebook for lifting. It’s a diagram (or sometimes a digital screen graphic on newer models) that tells you exactly how much weight you can lift, and where, without tipping the thing over. Tipping a telehandler isn’t just bad for the machine—it’s a major safety risk. Last year, we had a client call us panicking because their operator tried to lift a 4,000-pound pallet from 20 feet out, and the machine’s front wheels lifted off the ground. They only avoided a crash because the operator knew to set the forks down slowly and never tried that again. That’s why the load chart isn’t something you just glance at once and forget—it’s your go-to every single time you adjust the boom’s length or angle.

What makes a telehandler different from a forklift or a crane, though? Forklifts have a fixed mast, right? They can only lift straight up (mostly) from the front. Cranes have booms that move, but they’re designed for much heavier loads and have different weight limits. Telehandlers? They’ve got a boom that telescopes out, goes up and down, and even tilts forward or backward. That flexibility is why they’re so popular—one machine can do the work of a forklift, a small crane, and a lift all in one. But that same flexibility is exactly why the load chart is non-negotiable. Change the boom length? Change the height you’re lifting? Move the load closer or farther from the machine? All of that changes how much weight you can safely lift.

Let’s talk about the key numbers on a load chart, because if you don’t know what each one means, the chart is just a bunch of gibberish. First, there’s the “rated load capacity”—that’s the maximum weight the machine is designed to lift at its “ Rated Load Moment,” which is basically the sweet spot: boom fully retracted, load dead center, on level ground. For our most popular model, the Genie GTH-5519, that number is 5,500 pounds. But here’s where most people mess up: that 5,500 pounds only applies when the boom is tucked all the way in, and the load is right over the front wheels. If you extend the boom to 10 feet out, that 5,500 drops to around 4,800 pounds. Extend it to 19 feet (the max for that model)? Suddenly you’re only looking at 2,200 pounds. That’s a huge difference. I’ve seen guys try to cram a 5,000-pound pallet when the boom’s fully extended—they think “5,500 is the max, so it’ll work”—and that’s how you end up with a tip.

Then there’s the “load radius,” which is the horizontal distance from the center of the telehandler’s front wheels to the center of the load. That’s the main x-axis on the load chart, right? So as the radius gets bigger (you’re reaching farther out), the load capacity gets smaller. That’s a simple trade-off, but again, easy to overlook when you’re in a hurry. One job last spring, a subcontractor was rushing to get steel beams on a second floor. He didn’t check the load chart, just guessed how far he could reach. He ended up having his helper crawl under the boom to hook the beam because the load was too heavy to lift that far—total waste of time, and he could have gotten hurt. If he’d just pulled the telehandler 2 feet closer to the building, the load radius would have gone down, and he could have lifted the beam safely from the seat.

Wait, let’s not forget about “operating height” and “boom angle” either. The load chart also accounts for how high you’re lifting the load, because that affects the balance too. If the boom is at a steep angle (like 70 degrees from horizontal), the weight capacity is lower than when it’s at a shallower angle. Why? Because a steeper angle means the load is pulling more toward the top of the boom, which shifts the machine’s center of gravity forward. A shallower angle keeps more weight over the machine’s base, so you can lift more. It’s not just about how far out you reach—it’s about how high you’re lifting that load as you go.

Now, here’s the part that confuses a lot of people: load charts change depending on what’s attached to the boom. Do you have standard forks? That’s the most common attachment. But if you’re using a jib for lifting large objects like HVAC units, or a bucket for dirt, or a work platform for people? The load capacity drops even more. The attachment adds weight to the end of the boom, which means you have less capacity for your load. We always tell customers to check the load chart specifically for their attachment, not the base model. For example, the Genie GTH-5519’s standard load capacity is 5,500 pounds, but with a 6-foot jib attachment, that drops to 3,800 pounds. Small detail, big consequence.

Also, let’s talk about ground conditions, because that’s a huge factor most load charts mention too. The chart assumes you’re on level, solid ground—no mud, no sloped surfaces, no soft gravel. If you’re working on a slope, even a gentle 5 degrees, your load capacity goes down. If the ground is soft, the telehandler’s wheels can sink, which shifts the center of gravity and reduces stability. Last summer, we had a customer try to work on a muddy site, and he ignored the load chart’s note about soft ground. The front wheel sank 6 inches, and when he lifted a 4,000-pound load, the machine started tipping. He had to lower the load fast, and we ended up towing the telehandler out with our service truck. That could have been avoided if he’d just checked the ground conditions against the load chart’s warnings.

Now, you might be thinking, “Why can’t the load chart just tell me one number for every scenario?” Because physics. The center of gravity of a telehandler is a fixed point between the front and rear axles, right? When you add a load to the end of the boom, you’re shifting the overall center of gravity forward. If that center of gravity moves too far forward past the front wheels, the back end of the machine lifts off the ground—and that’s a tip. The load chart is just visualizing that math so you don’t have to do it in your head while you’re lifting. It’s not just a random set of numbers; each line on the chart is calculated to keep the center of gravity within the safe zone.

For newer telehandlers, a lot of them have load charts built into the dash screen now, which is way easier than pulling out a paper chart (that usually gets lost or crumpled in the truck). These digital load monitors will actually warn you if you’re getting too close to the max capacity, and some will even lock the boom from extending further if you exceed the limit. But here’s the catch with those: you still have to input the right weight of your load, the right boom length, and the right ground conditions. If you guess wrong on the load weight, the monitor will give you a false sense of safety. We’ve seen operators type in a load that’s 1,000 pounds lighter than it actually is, and the monitor lets them lift it—until the boom starts to tip.

Let’s do a quick example to make this concrete. Say you’re operating a JLG 1055, another one of our top sellers. This model has a max rated load of 10,000 pounds when the boom’s fully retracted, at 0 feet radius. If you extend the boom to 15 feet out, that number drops to 7,000 pounds. At 30 feet (its max boom length), the capacity is 3,500 pounds. Now, if you’re on a 2-degree slope, that 3,500 pounds drops by about 10% to 3,150. If you’re using a fork extension (which adds 50 pounds to the end of the boom), that’s another 50 pounds you have to subtract, so your actual max is 3,100. That’s how all the small details add up—every factor on the load chart matters.

So why is this important for you, the person renting or buying a telehandler? As a supplier, we’ve seen way too many people cut corners on load chart basics to save time. But cutting corners here doesn’t just lead to damage to the machine—it leads to downtime, injuries, and even fatalities. OSHA has reported that telehandler tip-overs are one of the top causes of construction equipment deaths, and almost all of those are caused by operators ignoring the load chart. Our job isn’t just to sell you a machine—it’s to make sure you use it safely and effectively, which means understanding that load chart isn’t a suggestion, it’s a rule.

Now, let’s talk about common mistakes we see with load charts, just so you can avoid them. First, mistaking boom height for load radius. A lot of operators think, “If I’m lifting 20 feet high, that means the load radius is 20 feet.” No—load radius is how far out you are horizontally, no matter how high you are. You can have a 20-foot height and a 10-foot radius, which is totally different. Second, forgetting to account for attachments. We had a guy last year using a grapple attachment for tree branches; he used the base model’s load capacity instead of the grapple’s, and he tried to lift 3,000 pounds that was too heavy for his setup. Third, not checking ground conditions. Even a small slope can drop your capacity by 15%, so don’t just assume the chart’s level-ground numbers apply. Fourth, ignoring the “no lift” zones on the load chart. Some charts have shaded areas where you can’t lift at all—usually when the boom is almost fully extended or at a steep angle. Those aren’t random; they’re the points where the machine is at risk of tipping.

Here’s a tip we give all our customers: keep a laminated copy of the load chart in the telehandler’s cab, right next to the operator’s seat. Don’t hide it in a toolbox or a binder. If it’s easy to see, you’re way more likely to check it before you lift. And if you’re using a digital load monitor, make a habit of verifying its readings against the printed chart every time you set up the machine. Monitors can glitch, but the paper chart (or the machine’s manual) is the official source.

At the end of the day, a telehandler is only as good as the person operating it. The load chart is your guide to getting the most out of the machine without putting anyone or anything at risk. If you’re in the market for a telehandler—whether you’re a small subcontractor or a big construction company—our team can walk you through load charts for any model, help you pick the right machine for your job, and even do a quick refresher on how to read the chart if you’re new to operating these machines. We’re not just a supplier; we’re a resource for keeping your job site running smoothly and safely. If you have questions, or you’re ready to rent or buy a telehandler that fits your needs, reach out to us to chat through the details. No sales pitch, just straight talk about what you need to get the job done right.

Articulated Boom Lifts References

  1. Occupational Safety and Health Administration (OSHA). (2022). Telehandler Safety Guidelines for Construction Operations. U.S. Department of Labor.
  2. American National Standards Institute (ANSI). (2021). Safety Standard for Telehandlers (ANSI/SIA A92.6).
  3. Construction Equipment Association (CEA). (2020). Telehandler Load Chart Best Practices for Job Sites.
  4. Genie Industries. (2023). Operator’s Manual for GTH Series Telehandlers: Load Chart Interpretations.
  5. JLG Industries. (2022). Digital Load Monitor Calibration and Usage Guide for Telehandlers.

Shandong Longqing Heavy Industry Co., Ltd.
As one of the most professional forklift manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to wholesale durable forklift in stock here from our factory. We also accept customized orders.
Address: No.3 Shanbo Road, Hi-Tech Zone, Jining City, Shandong Province
E-mail: lqzg@lonqing.com
WebSite: https://www.longqinglift.com/